Custom Search
RECENT POSTS

Wednesday, February 1, 2012

Dead Weight Tester: Animated Video





This is a video that I have found in Youtube explaining about the working of Dead Weight Tester. This video was uploaded by MensorCorporation
In the previous post I have explained about the principle and working of DWT. Now have a video to understand it more visually.



About this video: How a deadweight tester works to generate pressure for calibration and demonstration of the Mensor Deadweight tester model CPC5000 and the CPU5000 Control unit that automatically senses environmental conditions and adjusts for them.

Article Source: www.youtube.com




Read more...

Dead Weight Tester in Instrumentation





What is a Dead Weight tester in instrumentation?

Dead weights are usually used for pressure gauge calibration as they come with high accuracy, So they can be used as primary standard (as mentioned before).there are many types of them depending on the application and they are operated with oil (hydraulic) or with air (pneumatic).

 

Dead weight testers are the basic primary standard for accurate measurement of pressure. Dead weight testers are used to measure the pressure exerted by gas or liquid and can also generate a test pressure for the calibration of numerous pressure instruments.

Why dead weight tester called dead weight tester?

In dead weight tester, we put the weight on the weight stand of dead weight tester putting weight is reference weight which is to be calibrate  and further we applied pressure by moving piston ,when  applied pressure and reference weight(Pressure)is equal at  this condition reference weight will be zero(Dead).  therefore it is called dead weigh tester.

A deadweight tester (DWT) is a calibration standard which uses a piston cylinder on which a load is placed to make an equilibrium with an applied pressure underneath the piston.

The formula to design a DWT is based basically is expressed as follows :
p    =    F / A    [Pa]
where :
p     :    reference pressure    [Pa]
F     :    force applied on piston    [N]
A     :    effective area PCU    [m2]

Working of Dead Weight Tester :



 


1 - Hand pump                  2 - Testing Pump       3 - Pressure Gauge to be calibrated
4 - Calibration Weight       5 - Weight Support   6 - Piston
7 - Cylinder                      8 - Filling Connection

Working:

Dead weight testers are a piston-cylinder type measuring device. As primary standards, they are the most accurate instruments for the calibration of electronic or mechanical pressure measuring instruments.

They work in accordance with the basic principle that P= F/A, where the pressure (P) acts on a known area of a sealed piston (A), generating a force (F). The force of this piston is then compared with the force applied by calibrated weights. The use of high quality materials result in small uncertainties of measurement and excellent long term stability.

Dead weight testers can measure pressures of up to 10,000 bar, attaining accuracies of between 0.005% and 0.1% although most applications lie within 1 - 2500 bar. The pistons are partly made of tungsten carbide (used for its small temperature coefficient), and the cylinders must fit together with a clearance of no more than a couple of micrometers in order to create a minimum friction thus limiting the measuring error. The piston is then rotated during measurements to further minimize friction.

The testing pump (2) is connected to the instrument to be tested (3), to the actual measuring component and to the filling socket. A special hydraulic oil or gas such as compressed air or nitrogen is used as the pressure transfer medium. The measuring piston is then loaded with calibrated weights (4). The pressure is applied via an integrated pump (1) or, if an external pressure supply is available, via control valves in order to generate a pressure until the loaded measuring piston (6) rises and 'floats' on the fluid. This is the point where there is a balance between pressure and the mass load. The piston is rotated to reduce friction as far as possible. Since the piston is spinning, it exerts a pressure that can be calculated by application of a derivative of the formula P = F/A.

The accuracy of a pressure balance is characterized by the deviation span, which is the sum of the systematic error and the uncertainties of measurement.

Today's dead weight testers are highly accurate and complex and can make sophisticated physical compensations. They can also come accompanied by an intelligent calibrator unit which can register all critical ambient parameters and automatically correct them in real time making readings even more accurate.

To see the animated video of working of dead weight tester see the upcoming post. It includes a Youtube video provided by Mensor Corporation.

Article Source: www.sensorland.com

Read more...

Basics of Instrumentation & Control


To view more posts on BASICS : CLICK HERE

Pressure


To view more posts on PRESSURE : CLICK HERE

Flow


To view more posts on FLOW : CLICK HERE

Level


To view more posts on LEVEL : CLICK HERE

Temperature


To view more posts on TEMPERATURE : CLICK HERE

Analytical Instrumentation


To view more posts on Analytical Instrumentation : CLICK HERE
Related Posts Plugin for WordPress, Blogger...

About This Blog

Hai friends…welcome to my blog. This blog is exclusively for instrumentation engineering students which will provide sources for their reference and studies. As you all know Instrumentation is now a fast emerging and developing field in Engineering. This blog has different categories like PLC, SCADA, DCS, Sensors and Transducers, Computer control of process, Industrial Instrumentation, etc.

This blog will also provide an exclusive ‘ASK ME’ section where you can make any queries and share your ideas about instrumentation. The solution for your queries will be given to you by mail from best of my knowledge and reference.

So I wish this blog may be very useful for your studies and reference.

About Me

Keep In Touch

Follow Me!

Online Queries


Popular Posts