Custom Search
RECENT POSTS

Saturday, December 3, 2011

Thermocouples






Thermocouples

Thermocouples - types, principles and temperature ranges:

One of the most common industrial thermometer is the thermocouple. It was discovered by Thomas Seebeck's in 1822. He noted that a voltage difference appeared when the wire was heated at one end. Regardless of temperature, if both ends were at the same temperature there was no voltage difference. If the circuit were made with wire of the same material there was no current flow.
Schematic of a thermocouple



A thermocouple consists of two dissimilar metals, joined together at one end, and produce a small unique voltage at a given temperature. This voltage is measured and interpreted by a thermocouple thermometer.



The thermoelectric voltage resulting from the temperature difference from one end of the wire to the other is actually the sum of all the voltage differences along the wire from end to end
Thermocouples can be made from a variety of metals and cover a temperature range 200 oC to 2,600 oC. Comparing thermocouples to other types of sensors should be made in terms of the tolerance given in ASTM E 230.

Base metal thermocouples

Thermocouple
Maximum Temperature (oC)
Continuous
Spot
Copper-Constantan
400
500
Iron-Constantan
850
1,100
Chromel-Constantan
700
1,000
Chromel-Alumel
1,100
1,300
Nicrosil-Nisil
1,250
-
Tungsten-Molybdenum*
2,600
2,650

* Not used below 1250 oC.

Advantages with thermocouples

  • Capable of being used to directly measure temperatures up to 2600 oC.
  • The thermocouple junction may be grounded and brought into direct contact with the material being measured.

Disadvantages with thermocouples

  • Temperature measurement with a thermocouple requires two temperatures be measured, the junction at the work end (the hot junction) and the junction where wires meet the instrumentation copper wires (cold junction). To avoid error the cold junction temperature is in general compensated in the electronic instruments by measuring the temperature at the terminal block using with a semiconductor, thermistor, or RTD.
  • Thermocouples operation are relatively complex with potential sources of error. The materials of which thermocouple wires are made are not inert and the thermoelectric voltage developed along the length of the thermocouple wire may be influenced by corrosion etc.
  • The relationship between the process temperature and the thermocouple signal (millivolt) is not linear.
  • The calibration of the thermocouple should be carried out while it is in use by comparing it to a nearby comparison thermocouple. If the thermocouple is removed and placed in a calibration bath, the output integrated over the length is not reproduced exactly.

Thermocouple Types

Thermocouples are available in different combinations of metals or calibrations. The four most common calibrations are J, K, T and E. Each calibration has a different temperature range and environment, although the maximum temperature varies with the diameter of the wire used in the thermocouple.



Some of the thermocouple types have standardized with calibration tables, color codes and assigned letter-designations. The ASTM Standard E230 provides all the specifications for most of the common industrial grades, including letter designation, color codes (USA only), suggested use limits and the complete voltage versus temperature tables for cold junctions maintained at 32 oF and 0 oC.

There are four "classes" of thermocouples:
  • The home body class (called base metal),
  • the upper crust class (called rare metal or precious metal),
  • the rarified class (refractory metals) and,
  • the exotic class (standards and developmental devices).

 The home bodies are the Types E, J, K, N and T. The upper crust are types B, S, and R, platinum all to varying percentages. The exotic class includes several tungsten alloy thermocouples usually designated as Type W (something).


 Instrument
Temperature
Range
Accuracy
Recommended
(oF)
Maximum
(oF)
Type J probes
32 to 1336
-310 to 1832
1.8 to 7.9oF or 0.4% of reading above 32oF, whichever is greater
Type K probes
32 to 2300
-418 to 2507
1.8 to 7.9oF or 0.4% of reading above 32oF, whichever is greater
Type T probes
-299 to 700
-418 to752
0.9 to 3.6oF or 0.4% of reading above 32oF, whichever is greater
Type E probes
32 to 1600
32 to 1650
1.8 to 7.9oF or 0.4% of reading above 32oF, whichever is greater
Type R probes
32 to 2700
32 to 3210
2.5oF or 0.25% of reading, whichever is greater
Type S probes
32 to 2700
32 to 3210
2.5oF or 0.25% of reading, whichever is greater

Temperature Conversions

  • oF = (1.8 x oC) + 32
  • oC = (oF - 32) x 0.555
  • Kelvin = oC + 273.2
  • oRankin = oF + 459.67

ASTM Standards Related to Thermocouples

  • E 207-00...Method of Thermal EMF Test of Single Thermo element Materials by Comparison with a Secondary Standard of Similar EMF-Temperature Properties
  • E 220-02 Standard Test Method for Calibration of Thermocouples By Comparison Techniques
  • E 230-98e1..Temperature Electromotive Force (EMF) Tables for Standardized Thermocouples
  • E 235-88(1996)e1..Specification for Thermocouples, Sheathed, Type K, for Nuclear or Other High-Reliability Applications
  • E 452-02..Test Method for Calibration of Refractory Metal Thermocouples Using a Radiation Thermometer
  • E 574-00..Specification for Duplex, Base-Metal Thermocouple Wire with Glass Fiber or Silica Fiber Insulation
  • E 585/E 585M-01a ..Standard Specification for Compacted Mineral-Insulated, Metal-Sheathed, Base Metal Thermocouple Cable
  • E 601-81(1997)..Test Method for Comparing EMF Stability of Single-Element Base-Metal Thermocouples Materials in Air
  • E 608/E 608M-00. Standard Specification for Mineral-Insulated, Metal-Sheathed Base-Metal Thermocouples
  • E 696-00 Standard Specification for Tungsten-Rhenium Alloy Thermocouple Wire
  • E 710-86(1997) Standard Test Method for Comparing EMF Stabilities of Base-Metal Thermo elements in Air Using Dual, Simultaneous, Thermal-EMF Indicators
  • E 780-92(1998) Standard Test Method for Measuring the Insulation Resistance of Sheathed Thermocouple Material at Room Temperature
  • E 839-96 Standard Test Method for Sheathed Thermocouples and Sheathed Thermocouple Material
  • E 988-96(2002) Standard Temperature-Electromotive Force (EMF) Tables for Tungsten-Rhenium Thermocouples
  • E1129/E1129M-98 Standard Specification for Thermocouple Connectors
  • E 1159-98 Standard Specification for Thermocouple Materials, Platinum-Rhodium Alloys and Platinum
  • E 1350-97(2001) Standard Test Methods for Testing Sheathed Thermocouples Prior to, During and After Installation
  • E 1652-00 Standard Specification for Magnesium Oxide and Aluminum Oxide Powder and Crushable Insulators Used in the Manufacture of Metal-Sheathed Platinum Resistance Thermometers, Base Metal Thermocouples, and Noble Metal Thermocouples
  • E 1684-00 Standard Specification for Miniature Thermocouple Connectors
  • E 1751-00 Standard Guide for Temperature Electromotive Force (emf) Tables for Non-Letter Designated Thermocouple Combinations
  • E 2181/E 2181M-01 Standard Specification for Compacted Mineral-Insulated, Metal-Sheathed, Noble Metal Thermocouples and Thermocouple Cable 
 
 Article Source: www.engineeringtoolbox.com 


    0 comments:

    Basics of Instrumentation & Control


    To view more posts on BASICS : CLICK HERE

    Pressure


    To view more posts on PRESSURE : CLICK HERE

    Flow


    To view more posts on FLOW : CLICK HERE

    Level


    To view more posts on LEVEL : CLICK HERE

    Temperature


    To view more posts on TEMPERATURE : CLICK HERE

    Analytical Instrumentation


    To view more posts on Analytical Instrumentation : CLICK HERE
    Related Posts Plugin for WordPress, Blogger...

    About This Blog

    Hai friends…welcome to my blog. This blog is exclusively for instrumentation engineering students which will provide sources for their reference and studies. As you all know Instrumentation is now a fast emerging and developing field in Engineering. This blog has different categories like PLC, SCADA, DCS, Sensors and Transducers, Computer control of process, Industrial Instrumentation, etc.

    This blog will also provide an exclusive ‘ASK ME’ section where you can make any queries and share your ideas about instrumentation. The solution for your queries will be given to you by mail from best of my knowledge and reference.

    So I wish this blog may be very useful for your studies and reference.

    About Me

    Keep In Touch

    Follow Me!

    Online Queries


    Popular Posts